CCalclabhub

Science · 53 calculators

Capacitance Calculator

Capacitance tells you how much electric charge a capacitor holds for each volt of potential difference across it. The calculation is a simple division, but it connects three quantities that are often confused: charge, voltage and the energy stored in the electric field. This page explains the farad and its practical subunits, works through the arithmetic with a charge of 0.006 coulombs at 12 volts, and shows where mistakes usually creep in.

Capacitance

0.0005

Capacitance in microfarads
500
Stored energy
0.036
Charge in microcoulombs
6,000

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

The formula this calculator uses

C = Q / V

C
Capacitance, measured in farads
Q
Stored electric charge, measured in coulombs
V
Potential difference across the capacitor, measured in volts
E
Energy stored in the electric field, measured in joules

How to check the result by hand

  1. 1

    Express charge in coulombs and voltage in volts

    The defining ratio works only in base SI units. If the charge is quoted in microcoulombs, divide by one million before using it; if the voltage is quoted in millivolts, divide by one thousand. The default charge of 0.006 coulombs and voltage of 12 volts are already in the correct form. Writing the units beside each number at this stage makes a later prefix error much easier to catch.

  2. 2

    Divide charge by voltage

    Compute Q divided by V to obtain the capacitance in farads. With the defaults, 0.006 divided by 12 gives 0.0005 farads. The calculator keeps this value in a helper called capFarads and reuses it, so the farad and microfarad results can never disagree with one another. A result in the thousandths of a farad is typical of components used for smoothing rather than for tiny signal coupling.

  3. 3

    Rescale into microfarads

    Multiply the farad value by one million to express it in microfarads, the unit printed on most components. Here 0.0005 farads becomes 500.0 microfarads. This is a change of label only and does not alter the underlying capacitance. Check that the rescaled number is larger than the farad number by a factor of a million; a smaller answer means the conversion was applied in the wrong direction.

  4. 4

    Calculate the stored energy

    Multiply the charge by the voltage and then divide by two. With the default inputs, 0.006 times 12 is 0.07200000000000001, and halving it gives 0.036000000000000004 joules. The extra digits are a true floating-point result and should be preserved in the stored value, even though a written answer would normally be rounded. As a cross-check, evaluate one half of C times V squared and confirm that the two routes agree.

  5. 5

    Verify the charge and the relationships

    Rescale the charge into microcoulombs by multiplying by one million, giving 6000.0 microcoulombs for the defaults. Confirm that multiplying the capacitance of 0.0005 farads by 12 volts returns the original charge of 0.006 coulombs. Doubling the charge at a fixed voltage should double both the capacitance and the stored energy, while doubling the voltage at a fixed charge should halve the capacitance. These checks expose misplaced prefixes and misapplied conversions immediately.

Common Questions

How does the Capacitance Calculator work?

Divide the stored charge Q by the potential difference V to get capacitance C in farads, where one farad is one coulomb per volt. With a charge of 0.006 coulombs and a voltage of 12 volts the capacitance is 0.0005 farads, equivalent to 500.0 microfarads. The energy stored is half the product of charge and voltage, 0.036000000000000004 joules, and the same charge is 6000.0 microcoulombs.

What do I need to enter in the Capacitance Calculator?

It takes 2 inputs: Charge, Voltage. Fields that expect a unit say so next to the label.

Where does Capacitance come from?

It comes from C = Q / V — the defining relationship: capacitance is the charge stored per volt of potential difference. For a charge of 0.006 coulombs at 12 volts it gives 0.0005 farads.

What is the most common mistake with the Capacitance Calculator?

Entering microcoulombs instead of coulombs. The defining ratio requires the charge in coulombs. Entering 6000 for a charge that is actually 6000.0 microcoulombs makes the capacitance a million times too large. Convert prefixed units to base SI units before substituting, and write the unit beside every number so the scale is visible at a glance.

For worked examples, common mistakes and the limits of this formula, read the full How To Calculate Capacitance page.