CCalclabhub

Math · 75 calculators

Diagonal Of A Cube Calculator

A cube is the simplest three-dimensional solid: twelve equal edges, six identical square faces and a single number — the side length — that determines everything else. This page shows how to get the space diagonal, the face diagonal, the total surface area and the volume from that one measurement.

Last updated

Space diagonal

17.3205

Face diagonal
14.1421
Total surface area
600
Volume
1,000

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

The formula this calculator uses

Space diagonal d = s√3; face diagonal f = s√2; surface area SA = 6s²; volume V = s³

s
Side length (the length of one edge)
d
Space diagonal from a corner to the opposite corner
f
Face diagonal across one square face
SA
Total surface area, six times the side squared
V
Volume, the side raised to the third power

How to check the result by hand

  1. 1

    Identify the side length

    Find the length of one edge and call it s. Every other edge of a cube has exactly the same length, so a single measurement is enough. If the problem gives a face diagonal or a volume instead, reverse the appropriate formula first to recover s before continuing.

  2. 2

    Find the face diagonal with Pythagoras

    On one square face the diagonal is the hypotenuse of a right-angled triangle with two sides of length s. It is therefore √(s² + s²), which simplifies to s√2. With s = 10 that gives 14.142135623730951. This value is also the diameter of the circle that passes around the face.

  3. 3

    Extend into the interior for the space diagonal

    Combine the face diagonal with the upright edge in a second right-angled triangle. The space diagonal is √((s√2)² + s²) = s√3. For a side of 10, multiplying by the square root of three gives 17.32050807568877, comfortably longer than the face diagonal.

  4. 4

    Compute the total surface area

    One face has area s² and there are six identical faces, so the total is 6s². It is often useful to square the side once and keep that value, since it feeds both the surface area and, with one more multiplication, the volume. For s = 10 the surface area is 600.0 square units.

  5. 5

    Compute the volume and check the relationships

    Multiply the side by itself three times to get s³, which is 1000.0 for s = 10. Then check your work: the space diagonal should exceed the face diagonal, which should exceed the side, and the units should be length, length squared and length cubed respectively. Any mismatch means a formula was applied incorrectly.

Common Questions

How does the Diagonal Of A Cube Calculator work?

Multiply the side length by the square root of three for the corner-to-corner space diagonal, and by the square root of two for the diagonal across a single square face. Six times the side squared gives the total surface area, while the side cubed gives the volume. For a side of 10 the four results are 17.32050807568877, 14.142135623730951, 600.0 and 1000.0 respectively.

What do I need to enter in the Diagonal Of A Cube Calculator?

It takes 1 inputs: Side length. Fields that expect a unit say so next to the label.

Where does Space diagonal come from?

It comes from d = s√3 — the corner-to-corner distance through the interior. Apply Pythagoras across a face and then through the solid to obtain the factor of √3.

What is the most common mistake with the Diagonal Of A Cube Calculator?

Confusing the face diagonal with the space diagonal. These are different lines with different factors: s√2 lies in one face, while s√3 runs through the interior. If you need the longest distance inside the cube, always use the space diagonal. A useful check is that the answer must be bigger than the face diagonal, not smaller.

For worked examples, common mistakes and the limits of this formula, read the full How To Calculate The Diagonal Of A Cube page.