CCalclabhub

Health · 36 calculators

Mean Arterial Pressure Calculator

Mean arterial pressure is the average pressure driving blood through the arteries during one heartbeat. Because the relaxing phase of the cycle lasts about twice as long as the pumping phase, the standard approximation doubles the diastolic figure before averaging. This page explains the general formula and its arithmetic only; it is not personal medical advice.

Last updated

Mean arterial pressure

93.3333

Pulse pressure
40
MAP at diastolic + 10
100
Pulse pressure as share of systolic
33.33%

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

The formula this calculator uses

MAP = (systolic + 2 x diastolic) / 3

S
Systolic pressure, the peak pressure while the ventricles contract
D
Diastolic pressure, the pressure while the heart relaxes and refills
MAP
Mean arterial pressure, the time-weighted average over one cycle
PP
Pulse pressure, the difference between systolic and diastolic

How to check the result by hand

  1. 1

    Read the two pressures in the same units

    Write down the systolic number first and the diastolic number second, both in millimetres of mercury. For the worked reading these are 120 and 80 mmHg. Do not convert one of them to kilopascals while leaving the other alone, because the average would then combine incompatible quantities. A blood pressure reading is always quoted upper number first, so check that you have not reversed the pair before going further.

  2. 2

    Find the pulse pressure

    Subtract the diastolic pressure from the systolic pressure: 120 minus 80 gives 40.0 mmHg. This is the width of the pressure swing during each beat. It is a useful sanity check as you go, because the result should be positive for any ordinary reading and is usually much smaller than either of the two pressures themselves.

  3. 3

    Double the diastolic pressure and add systolic

    Multiply the diastolic value by two to get 160 mmHg, then add the systolic value of 120 to obtain 280 mmHg. This double weighting is the defining feature of the approximation and is what separates it from a plain average. If you accidentally weight both numbers equally, you will get 100 mmHg for this reading instead of the correct value.

  4. 4

    Divide by three to obtain the mean

    Divide the numerator by three: 280 divided by 3 gives 93.33333333333333 mmHg, displayed to two decimal places as about 93.33. Because three does not divide evenly into 280, the exact value has a repeating tail; keep the full value in calculations and round only for display. The result must lie between the diastolic and systolic pressures, and closer to the diastolic one.

  5. 5

    Work the comparison values

    For the higher-diastolic check, replace 80 with 90: (120 + 2 x 90) / 3 equals 100.0 mmHg. For the pulse pressure share, divide the 40.0 mmHg swing by the systolic 120 to get 0.3333333333333333, which renders as 33.33 per cent. The share output stores the raw decimal, so never add a multiplication by 100 inside the expression or the displayed figure will be magnified a hundredfold.

Common Questions

How does the Mean Arterial Pressure Calculator work?

Add the systolic pressure to twice the diastolic pressure, then divide by three. With a systolic of 120 and a diastolic of 80 mmHg, the mean arterial pressure is 93.33333333333333 mmHg, usually shown as about 93.33. Pulse pressure is systolic minus diastolic, here 40.0 mmHg, and as a share of the systolic number it is 0.3333333333333333, displayed as 33.33 per cent. Raising the diastolic to 90 while holding systolic at 120 gives a MAP of 100.0 mmHg.

What do I need to enter in the Mean Arterial Pressure Calculator?

It takes 2 inputs: Systolic pressure (mmHg), Diastolic pressure (mmHg). Fields that expect a unit say so next to the label.

Where does Mean arterial pressure come from?

It comes from MAP = (S + 2 x D) / 3 — add the systolic pressure to twice the diastolic pressure, then divide by three. The factor of two reflects the longer duration of diastole relative to systole in a normal cycle.

What is the most common mistake with the Mean Arterial Pressure Calculator?

Taking a plain average of the two numbers. Adding systolic and diastolic and dividing by two gives 100 mmHg for a reading of 120 over 80, rather than the correct 93.33333333333333. diastole lasts about twice as long as systole, so the lower number must be counted twice. This is the single most common error and it always biases the result upwards.

For worked examples, common mistakes and the limits of this formula, read the full How To Calculate Mean Arterial Pressure page.