CCalclabhub

Science · 51 calculators

Reynolds Number Calculator

The Reynolds number is a single dimensionless value that predicts whether a fluid flow will be smooth and layered or chaotic and mixed. It compares the inertial forces that keep a fluid moving with the viscous forces that damp it down. Engineers use it to decide whether flow in a pipe, around a wing or past a ship hull will be laminar or turbulent, and to make small-scale models behave like the real thing.

Last updated

Reynolds number

100,000

Kinematic viscosity (m²/s)
0
Dynamic pressure (Pa)
2,000
Velocity head (m)
0.2039

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

The formula this calculator uses

Re = rho v L / mu

Re
Reynolds number (dimensionless)
rho
Fluid density, in kilograms per cubic metre
v
Flow speed, in metres per second
L
Characteristic length, in metres
mu
Dynamic viscosity, in pascal-seconds

How to check the result by hand

  1. 1

    Gather the fluid properties

    Write down the density rho in kilograms per cubic metre and the dynamic viscosity mu in pascal-seconds for the fluid at the temperature of interest. For water near room temperature these are about 1,000 and 0.001 respectively. Property values drift with temperature, especially viscosity, so use figures that match your conditions.

  2. 2

    Choose the speed and characteristic length

    Set the flow speed v in metres per second and pick a representative length L in metres, such as the diameter of a pipe or the chord of a wing. Make sure every quantity is in SI units before you start. Using millimetres for the length while keeping density and viscosity in SI units is a common way to get an answer a thousand times too large.

  3. 3

    Optionally find the kinematic viscosity

    Divide the dynamic viscosity by the density to get nu = mu / rho. This is not strictly necessary for the main calculation, but it is a useful cross-check and lets you use the alternative form Re = v L / nu. With the worked values, 0.001 divided by 1,000 gives a kinematic viscosity of 1e-06 square metres per second.

  4. 4

    Compute the Reynolds number

    Multiply density, speed and length, then divide by dynamic viscosity: Re = rho v L / mu. For the worked case that is 1,000 times 2 times 0.05, which is 100, divided by 0.001, giving 100000.0. The units cancel completely, so report a plain number with no unit attached.

  5. 5

    Interpret the result and supporting quantities

    Compare the value with the relevant transition threshold. In pipe flow, 100000.0 is well above about 4,000 and therefore firmly turbulent. You can also report the dynamic pressure, 0.5 rho v squared, which is 2000 pascals here, and the velocity head, v squared over 2g, which is about 0.2039 metres, to describe the inertial side of the balance.

Common Questions

How does the Reynolds Number Calculator work?

Multiply the fluid density by its speed and a characteristic length, then divide by the dynamic viscosity. A low result means viscous forces dominate and the flow is laminar; a high result means inertia dominates and the flow is turbulent. For water with density 1,000 kilograms per cubic metre moving at 2 metres per second through a pipe 0.05 metres across, with viscosity 0.001 pascal-seconds, the Reynolds number is 100000.0.

What do I need to enter in the Reynolds Number Calculator?

It takes 4 inputs: Fluid density (kg/m^3), Flow speed (m/s), Characteristic length (m), Dynamic viscosity (Pa·s). Fields that expect a unit say so next to the label.

Where does Reynolds number come from?

It comes from Re = rho v L / mu — the defining relation. Multiply density, speed and characteristic length, then divide by dynamic viscosity. All four quantities use consistent SI units so the result is dimensionless.

What is the most common mistake with the Reynolds Number Calculator?

Using inconsistent units. The expression assumes SI units throughout: kilograms per cubic metre, metres per second, metres and pascal-seconds. Entering the length in millimetres while leaving the other terms in SI units produces an answer a thousand times too large, and the dimensionless result will silently look plausible.

For worked examples, common mistakes and the limits of this formula, read the full How To Calculate The Reynolds Number page.