CCalclabhub

Science · 63 calculations

Acoustics

How To Calculate Beat Frequency

When two tones of slightly different pitch sound together, they produce a throbbing or pulsing loudness known as beats. This page turns the two frequencies into four useful numbers: how fast the beats arrive, how long each beat cycle lasts, the average pitch that is heard, and the gap between the tones as a fraction of that average. The central idea is simple, but the difference between a beat rate and a pitch is widely misunderstood, so each quantity is derived separately below.

Last updated

Quick Answer

f_beat = |f1 - f2|

f1
Frequency of the first tone
f2
Frequency of the second tone
f_beat
Beat frequency, the rate of the loudness pulses
T_beat
Beat period, the time for one complete pulse cycle

Subtract one frequency from the other and take the absolute value to get the beat frequency in hertz. The beat period is the reciprocal of that difference, and the average frequency is the ordinary mean of the two tones. The relative difference divides the gap by the average, giving a decimal that displays as a percentage. For tones of 440 Hz and 442 Hz the beat frequency is 2 Hz, the period is 0.5 s, the average is 441 Hz and the relative difference is 0.0045351473922902496, displayed as about 0.4535 percent.

What Is Beat Frequency?

Beats are the periodic swelling and fading of loudness heard when two sounds of nearly equal frequency reach the ear at the same time. The two waves alternately reinforce and cancel one another: at some instants their crests arrive together and the sound is loud, while at others a crest meets a trough and the sound becomes quiet. This alternating pattern repeats steadily as long as both tones continue, producing the characteristic wobble that musicians listen for when tuning an instrument. The effect is a property of how the waves combine, not a property of either tone taken alone, and it disappears as soon as one source falls silent.

The physical mechanism is interference. When two waves overlap, their displacements add at every point and moment, a principle called superposition. If the waves are almost in step they add constructively and the amplitude grows; as one gradually slips ahead of the other they move out of step and add destructively, shrinking the amplitude. The time taken for the phase relationship to return to its starting condition is the beat period, and the number of such cycles each second is the beat frequency. The loudness therefore oscillates at a rate set by how quickly the two tones drift apart in phase, which is exactly the difference between their frequencies.

That is why the beat frequency equals the absolute difference of the two frequencies. If one tone is at 440 hertz and the other at 442 hertz, the faster wave gains two full cycles on the slower one every second, so the pair passes through two complete reinforce-and-cancel cycles per second and the beat frequency is 2 hertz. The absolute value matters because only the size of the gap is audible: 440 against 442 sounds identical to 442 against 440. A negative beat frequency would have no physical meaning, so subtracting in whichever order gives the positive result keeps the calculation well defined.

The beat period is simply the reciprocal of the beat frequency. A difference of 2 hertz means two pulses each second, so each pulse cycle lasts one half of a second, written 0.5 s. A difference of 10 hertz would give a period of 0.1 s, while a difference of 1 hertz gives a full second between peaks. Inverting the frequency is the same conversion used throughout wave physics, where period and frequency are always reciprocals. Confusing the two is common: the beat frequency counts how many pulses occur, whereas the beat period measures how long a single pulse takes, and one is the inverse of the other rather than a separate independent quantity.

The average frequency is the ordinary arithmetic mean of the two tones, found by adding them and dividing by two. For 440 Hz and 442 Hz that gives 441 Hz. This is the pitch that a listener perceives, because the ear averages the rapid oscillations that occur far faster than the slow loudness envelope. The average is not the same as the beat frequency: the pitch sits near 441 hertz while the pulses arrive only twice a second. Keeping these two scales apart is essential, since a claim that the sound has a frequency of 2 hertz would describe an inaudible rumble rather than the clear tone that is actually heard.

The relative difference expresses the gap between the tones as a fraction of their average. It is the beat frequency divided by the average frequency, so in the worked case it is 2 divided by 441, which equals 0.0045351473922902496. Expressed as a percentage that is roughly 0.4535 percent, a tiny mismatch that nevertheless produces an unmistakable pulsing sound. The calculator returns the raw decimal and the display layer converts it to a percentage, so the expression for this output contains no multiplication by one hundred. Reporting the value as a percentage and as a decimal at the same time is a frequent source of a factor-of-one-hundred error in written answers.

The pair of tones 440 Hz and 442 Hz is a natural example because 440 Hz is the standard concert pitch A used to tune orchestras. A second source two hertz sharp against that reference produces exactly two beats per second, which is slow enough to count and fast enough to hear clearly. This is why beats are so useful in tuning: a piano tuner listens to a reference note alongside the string being adjusted and tightens or loosens until the pulsing slows and finally stops. When the beats vanish, the two frequencies match and the strings are in tune. The same technique works for any pair of periodic signals, not just audible sound.

There are limits to when beats are perceived. The pulsing is most distinct when the two frequencies are close and their amplitudes are comparable, because then the cancellation at the quiet points is nearly complete. As the gap grows beyond roughly ten to twenty hertz, the ear stops resolving individual pulses and instead hears a rough, grating texture; wider still and the two tones are heard as separate pitches. Beats are also not a new frequency in the spectrum of the combined wave. Mathematically the sum of two close tones contains only the two original frequencies, and the slow envelope arises from their interference, so describing the beat frequency as a third audible note is incorrect.

The same arithmetic appears well beyond music. Radio receivers mix an incoming signal with a locally generated wave in a process called heterodyning, deliberately creating a beat at a lower frequency that is easier to amplify and filter. Ultrasonic testing and vibration analysis compare a measured frequency with a known reference and use the beat to detect small deviations. Measuring an unknown pitch by counting beats against a calibrated oscillator is a precise technique, because counting a few pulses per second is far easier than judging a small difference in pitch by ear. In every case the core calculation is unchanged: subtract, take the magnitude, invert for the period, average for the centre frequency, and divide to express the relative gap.

Formula

f_beat = |f1 - f2|

Formula page →

The rate of the loudness pulses equals the magnitude of the difference between the two frequencies. The absolute value removes any sign, since only the size of the gap matters.

SymbolMeaning
f1First frequency
f2Second frequency

T_beat = 1 / f_beat

Formula page →

Period is the reciprocal of frequency. A beat frequency of two pulses per second corresponds to a period of half a second between successive loud peaks.

SymbolMeaning
f_beatBeat frequency
T_beatBeat period

delta = f_beat / f_avg, where f_avg = (f1 + f2) / 2

Formula page →

Divide the gap by the mean of the two tones to express the mismatch as a fraction of the perceived pitch. The result is a raw decimal; the display layer renders it as a percentage, so no multiplication by one hundred is needed here.

SymbolMeaning
f_beatBeat frequency
f_avgAverage frequency
deltaRelative difference

How To Calculate Beat Frequency

  1. 1

    Write down the two frequencies

    Identify the frequencies of both tones and express them in the same unit, normally hertz. Check that both values are positive and that they refer to the same kind of wave. In the worked case the sources are at 440 Hz and 442 Hz, a difference of just two hertz.

  2. 2

    Subtract and take the absolute value

    Find the gap by subtracting one frequency from the other, then discard any minus sign. With 440 and 442 the difference is negative in one order and positive in the other, but the magnitude is 2 hertz either way. This magnitude is the beat frequency: two loudness pulses arrive each second.

  3. 3

    Average the two frequencies

    Add the tones and divide by two to estimate the pitch that is heard. Here 440 plus 442 is 882, and half of that is 441 Hz. This centre frequency sits between the two sources and is quite separate from the slow pulsing rate computed in the previous step.

  4. 4

    Invert the difference for the beat period

    Take the reciprocal of the beat frequency to find how long one pulse cycle lasts. One divided by 2 gives 0.5 s. Use the beat frequency here, not the average frequency, because it is the envelope that repeats twice a second rather than the underlying tone.

  5. 5

    Express the gap relative to the average

    Divide the beat frequency by the average frequency: 2 divided by 441 is 0.0045351473922902496. This is the relative difference as a raw decimal, which the display renders as roughly 0.4535 percent. Keep the decimal unmultiplied in the calculation and convert only when presenting the answer as a percentage.

Examples

Example 1: Concert A against a sharp reference — 440 Hz and 442 Hz

frequency1
440
frequency2
442
StepCalculationResult
Absolute difference|440 - 442|2
Average frequency(440 + 442) / 2441
Beat period1 / 20.5
Relative difference2 / 4410.0045351473922902496

Result: The two tones produce 2 beats per second with a beat period of 0.5 s, an average frequency of 441 Hz and a relative difference of 0.0045351473922902496, displayed as about 0.4535 percent.

Example 2: A lower pair — 330 Hz and 332 Hz

frequency1
330
frequency2
332
StepCalculationResult
Absolute difference|330 - 332|2
Average frequency(330 + 332) / 2331
Beat period1 / 20.5
Relative difference2 / 3310.006042296072507553

Result: The strings beat at 2 Hz with a period of 0.5 s and an average pitch of 331 Hz. The relative difference is 0.006042296072507553, displayed as about 0.6042 percent.

Example 3: A wider gap — 440 Hz and 450 Hz

frequency1
440
frequency2
450
StepCalculationResult
Absolute difference|440 - 450|10
Average frequency(440 + 450) / 2445
Beat period1 / 100.1
Relative difference10 / 4450.02247191011235955

Result: The tones beat at 10 Hz with a period of 0.1 s and an average frequency of 445 Hz. The relative difference is 0.02247191011235955, displayed as about 2.2472 percent.

Calculator

Beat frequency

2

Average frequency
441
Beat period
0.5
Relative difference
0.45%

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

Prefer a full-width tool? Open the Beat Frequency calculator page.

Common Mistakes

  • Forgetting the absolute value

    Subtracting in the wrong order can return a negative beat frequency, which has no physical meaning. The gap has a size but no direction, so always take the magnitude of the difference before reporting the answer.

  • Confusing the beat frequency with the average pitch

    For tones at 440 and 442 Hz the pulses arrive twice a second, but the note heard is near 441 Hz. Quoting 2 Hz as the pitch describes an inaudible rumble. Keep the slow envelope and the rapid carrier wave clearly separate.

  • Using the average frequency to find the period

    The beat period comes from the reciprocal of the beat frequency, not the average. Taking one divided by 441 would give a tiny interval that has nothing to do with the observed pulsing. The quantity that repeats slowly is the difference envelope.

  • Treating the beat as a new audible note

    The combined wave contains only the two original frequencies. The throbbing is an interference pattern in the amplitude, not a third tone at the difference frequency, so adding the beat frequency to a list of spectral components is wrong.

  • Multiplying the relative difference by one hundred inside the formula

    The relative difference output is stored as a raw decimal such as 0.0045351473922902496, and the display layer renders it as a percentage. Multiplying by one hundred again in the calculation would show 45.35 percent instead of about 0.4535 percent.

  • Adding the two frequencies instead of subtracting them

    Beats arise from a small mismatch, so the relevant operation is subtraction. Adding 440 and 442 gives 882 Hz, which is the sum frequency used in other areas of wave physics but bears no relation to the beat rate discussed here.

  • Expecting clear beats for widely separated tones

    Once the gap reaches roughly ten to twenty hertz the pulses blur into roughness, and beyond that the tones are heard separately. The formula still returns a number, but the perceptual phenomenon it describes is no longer present.

FAQ

What actually causes beats?

Beats come from interference between two waves of slightly different frequency. Their crests drift in and out of step, so the waves alternately reinforce and cancel. The result is a steady pulsing of loudness at a rate equal to the difference between the two frequencies.

Why do we take the absolute value of the difference?

Only the size of the frequency gap affects what is heard. Whether the first tone is higher or lower than the second makes no difference to the beat rate, so subtracting in either order and taking the magnitude always gives the correct positive answer.

What is the beat period and how is it found?

The beat period is the time between successive loud peaks and is the reciprocal of the beat frequency. At two beats per second the period is 0.5 s; at ten beats per second it is 0.1 s. It uses the beat frequency, not the average pitch.

How is the average frequency different from the beat frequency?

The average frequency is the mean of the two tones and is close to the pitch you hear, such as 441 Hz from 440 and 442 Hz. The beat frequency is the much smaller difference between them, just 2 Hz in that case, and controls only the speed of the pulsing.

What does the relative difference tell me?

It expresses the gap as a fraction of the average pitch, so it shows how closely matched the tones are in proportion rather than in hertz. For 440 and 442 Hz the value is 0.0045351473922902496 as a decimal, which displays as about 0.4535 percent.

Do beats happen with waves other than sound?

Yes. Any two periodic signals that overlap can beat, including radio waves, light and mechanical vibrations. Radio receivers exploit this deliberately when they mix an incoming signal with a locally generated one to produce a lower, more manageable frequency.

References

  1. [1]Wikipedia, Beat (acoustics) — https://en.wikipedia.org/wiki/Beat_(acoustics)
  2. [2]Wikipedia, Frequency — https://en.wikipedia.org/wiki/Frequency
  3. [3]Wikipedia, Wave interference — https://en.wikipedia.org/wiki/Wave_interference