Geometry
How To Calculate The Area Of An Annulus
An annulus is the ring-shaped region between two circles that share the same centre. Calculating its area means subtracting the smaller circle from the larger one, which reduces to a single expression in the two radii. This page explains that formula, shows how the ring width relates to the area, and works through examples so you can apply it to pipes, paths and washers with confidence.
Quick Answer
Area = pi * (R^2 - r^2)
- A
- Area of the annulus, in square units
- R
- Radius of the outer circle
- r
- Radius of the inner circle, the hole
- w
- Width of the ring, equal to R minus r
Subtract the square of the inner radius from the square of the outer radius, then multiply by pi. With the default radii of 5 and 3 the difference of squares is 16, so the ring area is 50.26548245743669 square units. The outer circle covers 78.53981633974483, the inner circle 28.274333882308138, and the ring has a width of 2.0 units.
What Is The Area Of An Annulus?
An annulus is the ring-shaped region lying between two concentric circles, which are circles that share the same centre. Its area is the area of the outer disk minus the area of the inner disk: pi times (R squared minus r squared), where R is the outer radius and r the inner radius. With the default radii of 5 and 3 the outer circle covers 78.53981633974483 square units, the inner circle covers 28.274333882308138, and the ring between them is 50.26548245743669 square units. The word comes from the Latin for a little ring, and the shape appears anywhere a circular boundary encloses a smaller circular hole.
The formula follows directly from subtracting one circle's area from another. A circle of radius R has an area of pi times R squared, and the inner cut-out has an area of pi times r squared, so what remains factorises neatly to pi times (R squared minus r squared). This factored form is the one the calculator uses because it needs only one multiplication after the two squares are found. It also shows that the answer depends on the squares of the radii rather than on their simple difference; expanding or factoring gives exactly the same result.
The ring width, sometimes called the thickness of the annulus, is simply R minus r, which is 2.0 units for radii of 5 and 3. Width and area are related but are not interchangeable: two rings of identical width can enclose very different areas if they sit at different distances from the centre. A narrow ring close to the centre covers far less ground than one of the same width near the outer rim, because the available circumference grows with radius. For a thin ring the area is approximately the width multiplied by the average circumference, a useful mental shortcut.
Because the radii are squared, a small increase in the outer radius adds a surprisingly large amount of area. Raising R from 5 to 6 while holding r at 3 changes the difference of squares from 16 to 27, so the area climbs from 50.26548245743669 to about 84.82, a gain of more than two thirds for a one-unit change. Raise the inner radius instead and the area falls, since the inner disk grows and removes more of the outer circle. The further out a change is made, the greater its effect, which is why the outer radius dominates the result.
Annular areas turn up constantly in engineering and everyday measurement. The cross-section of a hollow pipe, the flat face of a washer, the drum of a washing machine and a gravel path around a circular pond are all rings rather than full disks. To find how much material is needed for a pipe wall or how much surfacing covers a path, you subtract the hole from the outer circle. Manufacturers use the same calculation to estimate the mass of a metal ring from its area and density, and architects meet the shape when sizing a walkway around a fountain.
The annulus sits in a small family of circle quantities that are worth keeping distinct. The circumference of either boundary is two pi times its radius, and the area of a sector is a fraction of the area of a full circle. A full circle is simply the special case of the annulus with the inner radius set to zero, giving pi R squared with no subtraction needed. An ellipse generalises the circle by stretching it along two axes, and its area is pi times the product of the two semi-axes, but it does not share the concentric-ring construction.
Area is measured in square units, whether square metres, square centimetres or square inches, and the unit follows from the unit chosen for the radii. Both radii must be expressed in the same unit before they are squared, otherwise the subtraction has no meaning. If one radius is quoted in centimetres and the other in metres, convert one first. The result scales with the square of any unit change: doubling both radii multiplies the area by four, while the ring width merely doubles. This squared scaling is why a measurement error in a radius is amplified in the final area.
The most frequent mistake is confusing the radius with the diameter; if a problem quotes diameters, halve each one first. A second error is adding the two circle areas instead of subtracting them, which gives the combined area of both circles rather than the ring. A third is assuming the formula works when the circles are not concentric, in which case the shape is not an annulus. Finally, squaring the difference of the radii instead of the difference of their squares gives a much smaller number. Writing the expression as R squared minus r squared before substituting helps avoid all four slips.
The calculator stores pi as a constant named piVal and squares each radius in helpers named rOuterSq and rInnerSq. It reuses those squares for the ring area and for the two companion circle areas, so the default inputs produce 78.53981633974483 and 28.274333882308138 alongside the ring's 50.26548245743669. The ring width is computed separately as R minus r, giving 2.0 for the same inputs. Because every output depends on just those two radii, entering them correctly is the whole task.
Formula
A = pi * (R^2 - r^2)
Formula page →The outer circle's area minus the inner circle's area, factorised. With R equal to 5 and r equal to 3 the difference of squares is 16 and the area is 50.26548245743669 square units.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| R | Outer radius | length | Distance from the shared centre to the outside edge. Its square drives most of the area. |
| r | Inner radius | length | Distance from the shared centre to the hole. Increasing it removes area from the ring. |
A_outer = pi * R^2 ; A_inner = pi * r^2
Formula page →The two areas that are subtracted. For the default radii they are 78.53981633974483 and 28.274333882308138 square units respectively.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| R | Outer radius | length | Squared and multiplied by pi to give the full area enclosed by the outside edge. |
| r | Inner radius | length | Squared and multiplied by pi to give the area of the central hole. |
w = R - r
Formula page →The radial thickness of the ring, measured from the inner edge to the outer edge. With radii of 5 and 3 the width is 2.0 units.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| w | Ring width | length | A simple difference of the radii, in the same length unit. |
| R, r | Outer and inner radii | length | Both radii must be in the same unit before subtraction. |
How To Calculate The Area Of An Annulus
- 1
Identify the two radii
Find the radius of the outer circle, R, and the radius of the inner circle, r, making sure the two circles really share a centre. If a problem gives diameters instead, halve each one first, because the formula works only with radii. Check that both measurements use the same unit, converting one if necessary, and confirm which of the two is larger so that the subtraction comes out positive.
- 2
Square each radius
Multiply each radius by itself. With the default values, the outer radius of 5 gives 25 and the inner radius of 3 gives 9. Squaring both numbers before subtracting is essential: subtracting first and then squaring produces a much smaller and incorrect result. Keep the squares to hand, since the calculator reuses them for the two companion circle areas as well as the ring itself.
- 3
Subtract the inner square from the outer square
Compute R squared minus r squared. For the default radii this is 25 minus 9, which equals 16. This single number captures how much larger the outer circle is than the hole, and it is the only place where the two radii interact. A negative answer here means the radii were entered in the wrong order or that the supposed inner radius is actually the larger one.
- 4
Multiply the difference by pi
Multiply the difference of squares by pi, approximately 3.141592653589793. With a difference of 16 the annulus area is 50.26548245743669 square units. This multiplication converts the squared lengths into a proper area and is the last operation in the main formula. Carrying the full value of pi through the calculation avoids the small drift that comes from rounding it to 3.14 too early.
- 5
Check the companion quantities
As a sanity check, compute the full circle areas: pi times 25 is 78.53981633974483 and pi times 9 is 28.274333882308138. Subtracting the second from the first should return the ring area of 50.26548245743669, confirming the algebra. Finally find the ring width as 5 minus 3, which is 2.0 units. Agreement between the two routes means the radii, their order and the units are all consistent.
Examples
Example 1: The worked default — radii of 5 and 3
- outerRadius
- 5
- innerRadius
- 3
| Step | Calculation | Result |
|---|---|---|
| Square each radius | 5^2 and 3^2 | 25 and 9 |
| Subtract the squares | 25 - 9 | 16 |
| Multiply by pi | 3.141592653589793 * 16 | 50.26548245743669 |
| Ring area | pi * (25 - 9) | 50.26548245743669 square units |
Result: With R = 5 and r = 3 the annulus area is 50.26548245743669 square units; the outer circle is 78.53981633974483, the inner circle is 28.274333882308138 and the ring width is 2.0.
Example 2: A hollow pipe — radii of 10 and 7
- outerRadius
- 10
- innerRadius
- 7
| Step | Calculation | Result |
|---|---|---|
| Square each radius | 10^2 and 7^2 | 100 and 49 |
| Subtract the squares | 100 - 49 | 51 |
| Ring area | 3.141592653589793 * 51 | 160.22122533307945 square centimetres |
Result: The pipe wall has a cross-sectional area of 160.22122533307945 square centimetres, with a wall thickness of 3.0 centimetres.
Example 3: A circular path — radii of 8 and 6.5
- outerRadius
- 8
- innerRadius
- 6.5
| Step | Calculation | Result |
|---|---|---|
| Square each radius | 8^2 and 6.5^2 | 64 and 42.25 |
| Subtract the squares | 64 - 42.25 | 21.75 |
| Ring area | 3.141592653589793 * 21.75 | 68.329640215578 square metres |
Result: The path covers 68.329640215578 square metres, and its width is 1.5 metres.
Calculator
Area of the annulus
50.2655
- Outer circle area
- 78.5398
- Inner circle area
- 28.2743
- Ring width
- 2
Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.
Prefer a full-width tool? Open the The Area Of An Annulus calculator page.
Common Mistakes
Using diameters instead of radii
The formula needs radii, so entering a diameter directly squares a number twice as large as it should be and inflates the area fourfold. If the dimensions are given across the circle, halve each one first and only then square. Writing down R and r separately before substituting makes this error easy to spot.
Adding the two circle areas
Adding pi R squared and pi r squared gives the combined area of both disks, not the ring between them. The inner area must be subtracted because it is a hole. A quick check is that the answer has to be smaller than the outer circle on its own, which immediately rules out an addition.
Squaring the difference of the radii
Computing pi times (R minus r) squared is a different quantity altogether. The correct expression is the difference of the two squares, which factorises to (R minus r) times (R plus r). With radii of 5 and 3 the right difference is 16, whereas the square of the difference is only 4.
Mixing up the units of the two radii
If one radius is measured in centimetres and the other in metres, squaring and subtracting them is meaningless. Convert both to a single unit before starting, and carry that unit through to the answer as square units. The ring width in particular is only meaningful when both radii share the same scale.
Assuming the circles may be off-centre
An annulus requires two concentric circles. If the inner circle is displaced, the region between them is not an annulus and the simple ring width of R minus r no longer describes it. Check the geometry before using the width as a thickness.
Rounding pi too early
Replacing pi with 3.14 introduces a small but avoidable drift, and the error grows with the square of the radii. Use the full stored value, 3.141592653589793, or the calculator's built-in constant. For the default radii, rounding too soon changes the last few digits of the 50.26548245743669 result.
FAQ
What is an annulus?
An annulus is the flat ring-shaped region between two circles that share the same centre, like a washer or a doughnut viewed from above. The outer circle sets the outside edge and the smaller inner circle forms a hole. Its area is found by subtracting the inner circle's area from the outer circle's area. With radii of 5 and 3 that gives 50.26548245743669 square units.
What is the formula for the area of an annulus?
The area is pi multiplied by the square of the outer radius minus the square of the inner radius, written as A = pi (R squared minus r squared). It is just the difference of the two circle areas with the common factor pi taken outside. For the default radii of 5 and 3 the difference of squares is 16 and the area is 50.26548245743669.
How do I find the width of the ring?
Subtract the inner radius from the outer radius: w = R minus r. For radii of 5 and 3 the width is 2.0 units. This is a length, measured along a radius from the inner edge to the outer edge, and it should not be confused with the area. Two rings with the same width can have very different areas depending on how far out they sit.
What if the dimensions are given as diameters?
Halve each diameter to obtain its radius before using the formula. Squaring a diameter directly makes each circle four times too large, and the resulting ring area is four times the correct value. It is good practice to label the two halved values R and r on paper before substituting them, so you can see that the larger one comes first in the subtraction.
Why does increasing the outer radius add so much area?
Because the radius is squared, its effect grows with its size. Raising R from 5 to 6 while keeping r at 3 changes the difference of squares from 16 to 27, lifting the area from 50.26548245743669 to about 84.82. A change made further from the centre sweeps out a much larger band than the same change near the middle.
What units is the answer in?
Square units, inherited from the units of the radii. If radii are in metres the area is in square metres; if they are in centimetres the area is in square centimetres. Both radii must be converted to the same unit first. Doubling both radii quadruples the area but only doubles the ring width, so the area responds much more strongly to scale.
References
- [1], Annulus (mathematics) — https://en.wikipedia.org/wiki/Annulus_(mathematics)
- [2], Circle — https://en.wikipedia.org/wiki/Circle
- [3], Area — https://en.wikipedia.org/wiki/Area
