Math · 75 calculators
Area Of A Circle Sector Calculator
A circle sector is the slice cut out by two radii and the arc that joins their ends. Because it is simply a fraction of a complete circle, its area follows from one proportion: the central angle divided by 360 degrees. This page sets out that degrees convention explicitly, shows how the same fraction gives the arc length, and works through the numbers with a radius of 10 and an angle of 60 degrees.
Last updated
Sector area
52.3599
- Arc length
- 10.472
- Full circle area
- 314.1593
- Sector fraction
- 0.1667
Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.
The formula this calculator uses
Sector area A = (θ / 360) × πr²; arc length L = (θ / 360) × 2πr
- θ
- Central angle between the two radii, measured in degrees
- r
- Radius of the circle, measured in ordinary length units
- A
- Area of the sector, in square units
- L
- Arc length along the curved boundary of the sector
How to check the result by hand
- 1
Read off the radius and the central angle
Identify the radius r and the central angle θ, and confirm that the angle is quoted in degrees before doing anything else. This page and its calculator both use the degrees convention, so an angle of 60 means 60/360 of a full turn. If a question gives the answer in radians, convert it first by multiplying by 180/π. Write the two inputs down explicitly, since nearly every later error can be traced back to misreading one of them.
- 2
Compute the full circle area
Square the radius and multiply by π to obtain the area of the entire circle, which acts as the anchor for the calculation. With r = 10 the calculation is π × 10 × 10 = 314.1592653589793 square units. Keep this value at full precision rather than rounding it to 314, because the fraction in the next step will scale it. If the radius is in centimetres, the result is in square centimetres.
- 3
Find the sector fraction
Divide the central angle by 360 to find what share of the circle the slice occupies. For θ = 60 degrees the fraction is 60/360 = 0.16666666666666666, which is one sixth. A useful sanity check is that the fraction must lie between zero and one for a minor sector, and that common angles give familiar shares: 90 degrees is one quarter and 180 degrees is one half.
- 4
Multiply to get the sector area
Multiply the full circle area by the sector fraction to get the area of the slice. For the example that is 314.1592653589793 × 0.16666666666666666 = 52.35987755982988 square units. Equivalently, evaluate (60/360) × π × 10² in one line. The answer must be smaller than 314.1592653589793 and larger than zero; if it is not, the fraction was applied in the wrong direction.
- 5
Find the arc length and check the result
Apply the same fraction to the circumference to get the arc length: 2π × 10 × 0.16666666666666666 = 10.471975511965978 units. Then check the whole calculation for consistency. The sector area should be less than the circle area, the arc should be less than the full circumference of 62.83185307179586, and the area must be reported in square units while the arc stays in ordinary length units. If a perimeter is requested, remember to add the two radii to the arc.
Common Questions
How does the Area Of A Circle Sector Calculator work?
A sector occupies the same share of a circle's area as its central angle occupies of a full 360 degree turn. Multiply the full circle area πr² by θ/360 to get the sector area, and multiply the circumference 2πr by the same fraction to get the arc length. With radius 10 and a 60 degree angle, the full circle area is 314.1592653589793, the fraction is 0.16666666666666666, the sector area is 52.35987755982988 and the arc length is 10.471975511965978.
What do I need to enter in the Area Of A Circle Sector Calculator?
It takes 2 inputs: Radius, Central angle (degrees). Fields that expect a unit say so next to the label.
Where does Sector area come from?
It comes from A = (θ / 360) × πr² — take the area of the full circle and multiply by the fraction of a complete turn represented by the central angle. The divisor 360 applies only when the angle is measured in degrees.
What is the most common mistake with the Area Of A Circle Sector Calculator?
Forgetting to divide by 360. Using θπr² instead of (θ/360)πr² multiplies the answer by 360 and produces a slice larger than the entire circle. The divisor is the whole point of the calculation. A quick check is that any minor sector must have an area smaller than πr², so a result above that anchor flags the missing division immediately.
For worked examples, common mistakes and the limits of this formula, read the full How To Calculate The Area Of A Circle Sector page.
