CCalclabhub

Science · 63 calculations

Electricity

How To Calculate Electric Field Strength

The electric field strength between two charged parallel plates tells you how much push a charge will feel in the space between them. It is simply the voltage across the plates divided by the distance separating them. This page walks through the formula, the force and energy it produces, and the unit conversions that catch most people out.

Last updated

Quick Answer

E = V / d

E
Electric field strength, in volts per metre (V/m)
V
Potential difference between the plates, in volts
d
Perpendicular separation of the plates, in metres
q
Magnitude of the test charge, in coulombs

Divide the potential difference between the plates by their separation to get the electric field strength in volts per metre. Multiply by a test charge to find the force on it, and multiply the voltage by the charge to find the energy transferred. With 12 V across plates 0.02 m apart, the field is 600.0 V/m.

What Is Electric Field Strength?

An electric field is a region of space in which an electric charge experiences a force. Field strength, usually written E, is defined as the force per unit positive charge placed at a point, so its units can be given equally well as newtons per coulomb or as volts per metre. Between two large, flat, oppositely charged plates the field is very nearly uniform: its magnitude and direction are the same almost everywhere in the gap, apart from close to the edges. That uniformity is what makes the parallel-plate arrangement the standard teaching example and the one this page calculates.

The formula follows from equating two ways of describing the same work. Moving a charge q through a potential difference V transfers energy qV. The same charge placed in a field E feels a force qE, and pushing it a distance d against that force does work qE times d. Setting qV equal to qE times d and cancelling the charge leaves E = V / d. Notice that the charge cancels completely, so the field itself does not depend on the test charge you use to measure it. It is a property of the plates and the voltage applied to them.

Two inputs control the answer, and they act in opposite directions. Field strength is directly proportional to voltage, so raising the voltage from 12 V to 24 V while keeping the plates fixed doubles the field. It is inversely proportional to separation, so pulling the plates twice as far apart halves the field at the same voltage. In the default case, 12 V across a gap of 0.02 m gives 600.0 V/m; at double the distance, 0.04 m, the same voltage gives 300.0 V/m. Confusing which quantity sits on top of the fraction is the single most common source of a wrong answer.

Once the field is known, the force on any charge placed in it follows immediately from F = qE. A test charge of 0.001 C in a field of 600.0 V/m experiences a force of 0.6 N, directed from the positive plate towards the negative plate for a positive charge and the other way for a negative one. The field is calculated as though the test charge were not there, which is why it must be small enough not to distort the charge distribution on the plates. A large charge would rearrange the plate charges and change the very field you were trying to measure.

Force and energy are related but distinct, and mixing them up is easy. The force on a charge in the gap is qE, while the energy it gains when it crosses the full potential difference is qV. For the default values the energy is 12 multiplied by 0.001, which is 0.012 J. You can get the same figure from force times distance: 0.6 N across 0.02 m also gives 0.012 J. The energy depends only on the potential difference between the starting and ending points, not on the route taken, because an electrostatic field is conservative. That is why the two routes agree exactly.

The uniform-field formula assumes plates that are large compared with the gap between them. Real plates are finite, and near their edges the field lines bow outwards in what is called fringing, so the local field there is weaker and no longer points straight across. Close to the centre of the plates the approximation is excellent, and it improves further as the plate area grows relative to the separation. If you need the field right at an edge, a simple division of voltage by distance is no longer enough and a more detailed model is required.

Units deserve particular care because two different-looking systems are both correct. A volt per metre is exactly one newton per coulomb: a volt is a joule per coulomb and a joule is a newton metre, so the metre cancels. Separation must be entered in metres for the answer to come out in V/m. A gap of two centimetres is 0.02 m, not 2 m and not 0.2 m, and a millimetre is one thousandth of a metre. Entering centimetres directly makes the field a hundred times too small, an error that is easy to miss because the printed number still looks plausible.

The field between plates sits alongside several other familiar electrical quantities. Voltage is the potential difference that drives the field, current is the rate at which charge moves through a conductor placed in it, and resistance sets how much current flows for a given voltage. The energy stored in the field relates to the capacitance of the plates, and the power delivered to a circuit is the product of voltage and current. Knowing the field lets you see why a small gap at high voltage can break down the insulating air: the field, rather than the voltage alone, is what stresses the material.

Finally, the formula belongs to electrostatics and to slowly varying fields. When voltages change rapidly with time, magnetic effects appear and the simple relationship must be replaced by the full set of electromagnetic equations. It also assumes the space between the plates is empty or filled with a uniform dielectric; layers of different materials share the voltage in proportion to their properties. Within its range of validity, though, E = V / d is exact, easy to check, and a useful mental model: the same voltage across a smaller gap always produces a stronger field.

Formula

The potential difference divided by the perpendicular plate separation. Doubling V doubles the field; doubling d halves it.

SymbolMeaning
EElectric field strength
VPotential difference
dPlate separation

The field is force per unit charge, so multiplying by the charge gives the force. The direction depends on the sign of the charge.

SymbolMeaning
FForce on the charge
qCharge magnitude
EElectric field strength

Energy transferred to a charge moving through the full potential difference. It equals force times distance, qE times d. Half coverage follows by replacing V with a chosen fraction of the voltage.

SymbolMeaning
WEnergy transferred
qCharge magnitude
VPotential difference

How To Calculate Electric Field Strength

  1. 1

    Read the voltage across the plates

    Find the potential difference V between the two plates, in volts. This is the supply voltage if the plates are connected to a battery or power source. In the worked case it is 12 V. Make sure you use the voltage across the gap, not the rating of some other part of the circuit, and keep the sign out of it because field strength is a magnitude.

  2. 2

    Measure the separation in metres

    Measure the perpendicular distance d from one plate to the other and convert it to metres. Two centimetres becomes 0.02 m; one millimetre becomes 0.001 m. This conversion is where most errors creep in, because calculators will happily accept a centimetre value and return a number that looks reasonable but is wrong by a factor of a hundred.

  3. 3

    Divide voltage by separation

    Compute E = V / d. With 12 V and 0.02 m the field is 12 divided by 0.02, which is 600.0 V/m. The units follow from the division: volts divided by metres gives volts per metre. Check the direction of the change: a larger voltage or a smaller gap must give a larger field, so if your answer moves the other way the fraction is upside down.

  4. 4

    Find the force and the field at a wider gap

    Multiply the field by the test charge to get F = qE, so 0.001 C in 600.0 V/m feels 0.6 N. For a wider gap, divide the same voltage by the new distance: at 0.04 m the field is 300.0 V/m, exactly half the original. Notice that the charge plays no part in the field itself; it only affects the force that the field produces.

  5. 5

    Work out the energy transferred

    Multiply the voltage by the charge to get W = qV, which is 12 multiplied by 0.001, or 0.012 J. As a cross-check, multiply the force by the distance: 0.6 N times 0.02 m also gives 0.012 J. Agreement between the two routes confirms that the field, force and distance are all consistent with one another.

Examples

Example 1: Field between the default parallel plates

voltage
12 V
plateSeparation
0.02 m
testCharge
0.001 C
StepCalculationResult
Potential differenceread from the supply12 V
Separation in metres2 cm converted0.02 m
Field strengthE = 12 / 0.02600.0 V/m

Result: The electric field strength between the plates is 600.0 V/m, directed from the positive plate towards the negative plate.

Example 2: Force on a small test charge

voltage
12 V
plateSeparation
0.02 m
testCharge
0.001 C
StepCalculationResult
Field from voltage and gap12 / 0.02600.0 V/m
Force on the chargeF = 600.0 x 0.0010.6 N

Result: The force on the 0.001 C test charge is 0.6 N, pointing from the positive plate to the negative plate.

Example 3: Wider gap, weaker field, energy gained

voltage
12 V
plateSeparation
0.02 m
testCharge
0.001 C
StepCalculationResult
New separation0.02 x 20.04 m
Field at double distanceE = 12 / 0.04300.0 V/m
Energy gained by the chargeW = 12 x 0.0010.012 J

Result: Doubling the separation gives a field of 300.0 V/m, and the charge gains 0.012 J of energy crossing the gap.

Calculator

Electric field strength

600

Force on charge
0.6
Field at double the distance
300
Energy gained by charge
0.012

Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.

Prefer a full-width tool? Open the Electric Field Strength calculator page.

Common Mistakes

  • Confusing field strength with force

    Field strength is force per unit charge, measured in V/m or N/C, while force is measured in newtons. Asking for the field and answering in newtons mixes two different quantities. Multiply by a charge only when the question asks for the force on that specific charge.

  • Leaving the separation in centimetres

    The formula requires metres. A gap of 2 cm must be entered as 0.02 m; typing 2 returns a field a hundred times too small. Convert every length to metres before dividing, and sanity-check the result: a modest voltage across a small gap should give a field in the hundreds of volts per metre.

  • Reversing the fraction

    Writing E = d / V instead of V / d turns 600.0 V/m into a tiny fraction. Remember the direction of the effect: a bigger voltage must strengthen the field and a bigger gap must weaken it. If your answer moves the wrong way when you change an input, the fraction is upside down.

  • Forgetting that the field is independent of the test charge

    Some learners divide the voltage by the charge, or multiply the field by the charge when only the field was requested. The charge cancels out when the formula is derived, so the field depends on the plates alone. The charge matters only when you move on to the force or the energy.

  • Assuming the field is uniform right up to the edges

    Real plates are finite and their field lines fringe outwards near the rim, so the simple division applies only away from the edges. Applying it at an edge or for plates whose separation is comparable to their size gives a misleading answer. Treat the uniform-field result as a centre-of-plate approximation.

  • Adding the voltages of the two plates together

    The voltage across the gap is the potential difference between the plates, already a single number. Doubling it because there are two plates produces a field twice too large. Read the potential difference directly from the supply or meter and use it once.

FAQ

What unit is electric field strength measured in?

Volts per metre, written V/m, is the standard unit. It is exactly equivalent to newtons per coulomb, because a volt is a joule per coulomb and a joule is a newton metre. Both describe force per unit charge, so either is correct, though V/m suits the voltage-and-distance formula best.

Why does the test charge not appear in the field formula?

The field is a property of the charges on the plates and the voltage between them. When you equate the two expressions for work, the charge appears on both sides and cancels. It returns only when you ask for the force on a particular charge, through F = qE.

What happens to the field if the plates are moved twice as far apart?

At the same voltage the field halves, because separation sits in the denominator. In the worked case the field falls from 600.0 V/m at 0.02 m to 300.0 V/m at 0.04 m. The energy a charge gains crossing the gap is unchanged, since that depends on voltage rather than distance.

Is the field really the same everywhere between the plates?

Almost, but not quite. For plates that are large compared with their separation the field near the centre is very nearly uniform and the formula is excellent. Close to the edges the lines fringe outwards and the field weakens and bends, so the simple division is only an approximation there.

How is the energy gained by a charge related to the field?

The energy crossing the whole gap is qV, which is the same as the force qE multiplied by the distance d. For the default values both routes give 0.012 J. The equality works because an electrostatic field is conservative, so the energy depends only on the endpoints.

When does this formula stop being valid?

It assumes a steady or slowly changing field, a uniform gap and empty space or a single uniform dielectric between the plates. Rapidly changing voltages introduce magnetic effects, and layered dielectrics share the voltage unevenly. In those cases the simple division must be replaced by a fuller electromagnetic treatment.

References

  1. [1]Wikipedia, Electric field — https://en.wikipedia.org/wiki/Electric_field
  2. [2]Wikipedia, Voltage — https://en.wikipedia.org/wiki/Voltage
  3. [3]Wikipedia, Electric potential — https://en.wikipedia.org/wiki/Electric_potential