Electricity
How To Calculate Electric Potential Energy
Electric potential energy is the energy stored by a charge because of where it sits in an electric potential. It is found by multiplying the charge in coulombs by the potential in volts, which gives a result in joules. This page shows how to work it out, why the relation is linear in both quantities, and how to avoid the usual unit and sign errors.
Last updated
Quick Answer
U = q x V
- U
- Electric potential energy, in joules
- q
- Electric charge, in coulombs
- V
- Electric potential at the position of the charge, in volts
Multiply the charge by the electric potential at its location. A charge of two coulombs at a potential of twelve volts stores twenty-four joules. Doubling the charge doubles the energy to forty-eight joules, halving the potential gives twelve joules, and a charge of two coulombs is needed to store twenty-four joules at twelve volts.
What Is Electric Potential Energy?
The electric potential energy of a charge placed at a point of given electric potential is the product of the charge and the potential. Written as U equals q times V, the relation gives an answer in joules whenever the charge is measured in coulombs and the potential in volts. A charge of two coulombs sitting at a potential of twelve volts therefore stores twenty-four joules. The quantity describes energy associated with position in an electric field, not energy of motion. It is a scalar, so it has a magnitude and a sign but no direction, which makes it much simpler to combine than force or field strength.
To understand potential, think of it as energy per unit charge. One volt is defined as one joule per coulomb, so a twelve-volt potential means that each coulomb of charge placed there would carry twelve joules of potential energy. Multiplying by the actual charge simply scales that per-charge value up to the charge you have. This is why the units work out so cleanly: coulombs times joules per coulomb leaves joules. Dimensional consistency is a useful check, because a result that does not come out in joules usually means a unit was converted incorrectly.
A close analogy is gravitational potential energy near the Earth's surface. There, a mass at a height stores energy equal to mass times gravitational field strength times height, because the field supplies a potential that grows with position. In the electrical case the charge plays the part of the mass, and electric potential plays the part of height multiplied by field strength. A positive charge naturally moves towards lower potential, just as a mass falls towards lower height, releasing stored energy as it goes. The analogy is not perfect because electric charge can be negative as well as positive, so an electron moves in the opposite direction to a proton in the same field.
The defining feature of the relation is its linearity in both inputs. Doubling the charge while holding the potential fixed doubles the stored energy, and doubling the potential while holding the charge fixed does exactly the same. With the default values, doubling the charge to four coulombs at twelve volts gives forty-eight joules, while halving the potential to six volts gives twelve joules. Neither input is squared and there is no hidden constant, so the scaling is easy to predict. This also means the inverse problem is just as simple: to store twenty-four joules at twelve volts you need twenty-four divided by twelve, which is two coulombs.
The sign of the charge matters and is often overlooked. Because U equals q times V, a negative charge at a positive potential has negative potential energy, and a positive charge at a negative potential does too. A negative value does not mean the energy is missing; it records that the charge would have to do work to move to the chosen zero of potential, and that the zero is simply a reference. What has physical meaning is the change in energy between two positions, not the absolute value at one point. Keeping the sign of q in the calculation is essential, because dropping it reverses the predicted direction of energy transfer.
That reference point deserves a moment of attention. Electric potential is only defined relative to an arbitrary zero, often taken at infinity or at the ground terminal of a circuit. Changing the zero shifts every potential by the same constant and therefore changes every value of q times V by q times that constant. Differences between two potentials are unaffected, which is why voltage, being a difference, is the measurable quantity. For a single isolated calculation the convention must still be stated, because quoting a potential without saying what it is measured against leaves the energy ambiguous. In practical circuit work the agreed reference is usually the common return conductor.
The connection with work makes the formula more than a definition. In a conservative electric field, the work done in moving a charge between two points equals the charge times the potential difference between them, and it is independent of the path taken. A charge released at higher potential for its sign will accelerate and convert potential energy into kinetic energy, while pushing it the other way requires an external source of work. Batteries do exactly this: they use chemical energy to move charge to a higher potential, storing energy that can later be released to a circuit. The product q times V quantifies the energy exchanged in each of these processes.
Two related forms are worth knowing. In a uniform field, potential changes linearly with distance, so a charge separated from a reference plane by a distance d in a field of strength E has energy q times E times d. For a capacitor, the energy stored is one half times the capacitance times the square of the voltage, which differs from q times V because the charge builds up gradually as the capacitor charges rather than arriving all at once. Confusing the two expressions is common, but they describe different situations. The simple product in this calculator applies to a point charge at a specified potential, which is the case most students meet first.
The worked numbers make the behaviour concrete. With a charge of two coulombs and a potential of twelve volts, the energy is twenty-four joules; at double the charge it is forty-eight joules, at half the potential it is twelve joules, and the charge needed for twenty-four joules is two coulombs. These are deliberately round figures so the scaling is visible at a glance. This page presents general physics education, and real problems may involve potentials that vary with position or charges distributed over a surface rather than concentrated at a point. In those cases the same idea is applied by summing or integrating the contributions, but the underlying product remains the building block.
Formula
U = q x V
Formula page →The primary relation. Multiply the charge by the electric potential at its location. Coulombs times volts gives joules directly, with no conversion factor.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| q | Electric charge | C | Measured in coulombs; keep the sign, because a negative charge at a positive potential gives negative energy. |
| V | Electric potential at the charge | V | Measured in volts relative to a stated reference, where one volt is one joule per coulomb. |
| U | Electric potential energy | J | The stored energy in joules, linear in both the charge and the potential. |
delta U = q x (Vb - Va)
Formula page →Moving a charge between two points changes its potential energy by the charge times the potential difference. The result depends only on the endpoints in a conservative field.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| q | Electric charge being moved | C | The same signed charge as in the primary formula, in coulombs. |
| Vb - Va | Potential difference between the endpoints | V | Final potential minus initial potential, measured in volts. |
| delta U | Change in potential energy | J | Positive when work must be supplied, negative when the field releases energy. |
U = q x E x d
Formula page →In a uniform field the potential changes linearly with distance, so the potential difference equals field strength times distance along the field. Substitution gives this equivalent form.
| Symbol | Meaning | Unit | Notes |
|---|---|---|---|
| q | Electric charge | C | Charge in coulombs, carrying its sign. |
| E | Electric field strength | V/m | Uniform field strength in volts per metre, equivalent to newtons per coulomb. |
| d | Distance along the field | m | Separation measured parallel to the field direction, in metres. |
How To Calculate Electric Potential Energy
- 1
Write down the charge in coulombs
Take the charge q in coulombs and keep its sign. If the value is given in microcoulombs or millicoulombs, convert it first by multiplying by one millionth or one thousandth respectively. The sign matters because a negative charge at a positive potential stores negative energy, and discarding it reverses the direction of any energy transfer you go on to predict.
- 2
Write down the potential in volts
Take the electric potential V at the position of the charge, measured relative to a stated reference such as the ground terminal of a circuit. One volt is one joule per coulomb, so this number is the energy available to each coulomb of charge at that point. Potential differences are what can be measured directly, so make sure the quoted value refers to the same zero as any other value you compare it with.
- 3
Multiply charge by potential
Multiply q by V to obtain the electric potential energy in joules. With the default charge of two coulombs and potential of twelve volts, the product is twenty-four joules. There is no squaring and no conversion constant in this step: coulombs times volts is already joules. Check the size of the answer against the one-joule-per-coulomb-per-volt definition as a quick guard against a stray factor of a thousand.
- 4
Check the scaling cases
Because the relation is linear in both inputs, the related results follow without new arithmetic. Doubling the charge to four coulombs at twelve volts gives forty-eight joules, and halving the potential to six volts with the original charge gives twelve joules. If either of these does not come out as exactly double or half the main answer, an input has been entered incorrectly or an extra factor has crept into the calculation.
- 5
Solve the inverse question
To find the charge needed for a chosen energy, divide that energy by the potential. For a target of twenty-four joules at twelve volts, twenty-four divided by twelve gives two coulombs, which matches the original input and confirms the arithmetic. This rearrangement is the same relation read backwards, so it inherits the same units and the same dependence on the sign convention used for the potential.
Examples
Example 1: Default case — two coulombs at twelve volts
- charge
- 2
- potential
- 12
| Step | Calculation | Result |
|---|---|---|
| Multiply charge by potential | 2 x 12 | 24 |
| Energy at double the charge | 4 x 12 | 48 |
| Energy at half the potential | 2 x 6 | 12 |
| Charge needed for 24 joules | 24 / 12 | 2 |
Result: A charge of 2 coulombs at a potential of 12 volts stores 24 joules; doubling the charge gives 48 joules, halving the potential gives 12 joules, and a charge of 2 coulombs is needed to store 24 joules at this potential.
Example 2: Three coulombs at nine volts
- charge
- 3
- potential
- 9
| Step | Calculation | Result |
|---|---|---|
| Multiply charge by potential | 3 x 9 | 27 |
| Energy at double the charge | 6 x 9 | 54 |
| Energy at half the potential | 3 x 4.5 | 13.5 |
| Charge needed for 24 joules | 24 / 9 | 2.6666666666666665 |
Result: A charge of 3 coulombs at a potential of 9 volts stores 27 joules; doubling the charge gives 54 joules, halving the potential gives 13.5 joules, and storing 24 joules at this potential requires 2.6666666666666665 coulombs.
Example 3: Half a coulomb at twenty volts
- charge
- 0.5
- potential
- 20
| Step | Calculation | Result |
|---|---|---|
| Multiply charge by potential | 0.5 x 20 | 10 |
| Energy at double the charge | 1 x 20 | 20 |
| Energy at half the potential | 0.5 x 10 | 5 |
| Charge needed for 24 joules | 24 / 20 | 1.2 |
Result: A charge of 0.5 coulombs at a potential of 20 volts stores 10 joules; doubling the charge gives 20 joules, halving the potential gives 5 joules, and storing 24 joules at this potential requires 1.2 coulombs.
Calculator
Electric potential energy
24
- Energy at double the charge
- 48
- Energy at half the potential
- 12
- Charge needed for 24 joules
- 2
Values update as you type. This calculator covers the single scenario its formula assumes — see Common Mistakes for what it leaves out.
Prefer a full-width tool? Open the Electric Potential Energy calculator page.
Common Mistakes
Confusing potential with potential energy
Potential is energy per unit charge and is measured in volts, while potential energy is the total energy of a particular charge and is measured in joules. Multiplying them is the step that converts one to the other, so treating a voltage directly as an energy leaves out the charge entirely.
Forgetting to convert the charge to coulombs
Charges are often quoted in microcoulombs or millicoulombs. Entering those numbers as coulombs inflates the answer by a factor of a million or a thousand. Convert to coulombs before multiplying, and check that the result has a plausible size in joules.
Dropping the sign of the charge
A negative charge at a positive potential has negative potential energy. Removing the minus sign changes the sign of the answer and reverses the predicted direction of energy flow. Keep the sign throughout and interpret a negative value relative to the chosen zero.
Treating the absolute value as physically meaningful
Electric potential is defined relative to an arbitrary zero, so the value of q times V depends on that choice. Only differences in potential energy correspond to measurable work. State the reference before quoting an absolute value, especially when comparing two positions.
Using the capacitor energy formula by mistake
A capacitor stores one half times capacitance times voltage squared, because its charge accumulates gradually. That is not the same as q times V for a point charge placed at a fixed potential. Applying the capacitor expression here introduces an unjustified factor of one half and a squared voltage.
Mixing up energy, force and field strength
Potential energy is a scalar measured in joules, whereas electric field strength is a vector measured in volts per metre and force is measured in newtons. Substituting a field strength for a potential, or a force for an energy, breaks the units. Check that the inputs are a charge and a potential before multiplying.
FAQ
What is electric potential energy?
It is the energy a charge possesses because of its position in an electric potential. It equals the charge multiplied by the potential at that point, is measured in joules, and changes when the charge moves to a place with a different potential.
What is the difference between electric potential and potential energy?
Electric potential is energy per unit charge, measured in volts, and belongs to a point in space. Potential energy belongs to a particular charge placed there, is measured in joules, and is found by multiplying the potential by the charge.
What units should I use?
Use coulombs for charge and volts for potential. Their product is joules with no conversion factor, because one volt is defined as one joule per coulomb. Convert any microcoulombs or millicoulombs to coulombs first.
Can electric potential energy be negative?
Yes. Since energy equals charge times potential, a negative charge at a positive potential gives a negative value. The sign simply records the position relative to the chosen zero of potential; only changes in energy between two points are directly measurable.
What happens if I double the charge or the potential?
Either change doubles the stored energy, because the relation is linear in both inputs. With the default values, doubling the charge gives forty-eight joules and halving the potential gives twelve joules, both measured against the original twenty-four joules.
How is this related to the energy stored in a capacitor?
A capacitor stores one half times capacitance times voltage squared, because its charge builds up gradually during charging. The simple product of charge and potential applies to a charge placed at a fixed potential, which is a different situation.
References
- [1], Electric potential energy — https://en.wikipedia.org/wiki/Electric_potential_energy
- [2], Electric potential — https://en.wikipedia.org/wiki/Electric_potential
- [3], Coulomb — https://en.wikipedia.org/wiki/Coulomb
